The City of Calgary Land Use Bylaw 1P2007
Top of page
PART 3: RULES GOVERNING ALL DISTRICTS
Division 1: Public Realm Setbacks
Purpose
2
When considering a development permit application for a parcel adjacent to a street right-of-way referenced in Table 1, the Development Authority must require that the building be set back from the basic right-of-way by a distance equal to:
2.2
Where the Development Authority is considering a relaxation of the required setbacks referenced in Table 1, the Development Authority must consider the technical feasibility of the relaxation, including but not limited to: emergency vehicle and motor vehicle loading requirements, installation and maintenance of utility line assignments, and the installation and maintenance of public realm surface improvements.
3
When considering an application for a development permit for a discretionary use, the Development Authority may require that a building must not be constructed within a future corner cut-off at an intersection.
4
Portions of a parcel within the Required Setbacks referenced in Table 1 may be used by an applicant for the purposes of calculating landscaped area, floor area ratio and units per hectare.
Division 2: Airport Vicinity Rules
Airport Vicinity Regulations
54
When making a decision on a development permit the Development Authority must comply with the requirements of:
Division 3: Floodway, Flood Fringe and Overland Flow
Floodway, Flood Fringe and Overland Flow
55
For parcels located in the floodway, flood fringe or overland flow area, the requirements of this Division apply and prevail when there is any conflict between the requirements of this Division and any other requirements of this Bylaw.
Floodway Regulations
2
Subject to subsection (1), in the floodway only those permitted and discretionary uses which are listed below, and which are also listed in the land use district for which the parcel is designated, may be allowed as permitted and discretionary uses:
New Buildings and Alterations
57
1
No new buildings or other new structures are allowed in the floodway, except for the replacement of existing Accessory Residential Buildings, Backyard Suites, Duplex Dwellings, Secondary Suites, Semi-detached Dwellings and Single Detached Dwellings on the same building footprint.
Alterations to the Floodway and Riverbanks
58
On those areas of land within the floodway that are subject to municipal jurisdiction, no alterations shall be made to a floodway and no structures including, but not limited to, berms, decks, docks, fences, gates, patios, rip-rap or walls shall be constructed on, in or under a floodway unless those structures are being constructed by, or on behalf of, the City for the purpose of erosion control, where the primary purpose is to protect public infrastructure.
59
1
Only those goods that are easily moveable may be stored on a parcel in the flood fringe or the overland flow area.
2
Unless stated in subsection (3), all buildings must be set back 6.0 metres from the edge of the floodway.
c
all electrical and mechanical equipment within a building shall be located at or above the designated flood level; and
a
an addition that does not increase the gross floor area of the building by more than 10.0 per cent of the gross floor area legally existing as of June 09, 2014; and
b
a fence, gate, deck, landing, patio, skateboard and sports ramp, air conditioning unit, satellite dish, hot tub, above ground private swimming pool, and an Accessory Residential Building.
3
Notwithstanding subsection (1) and (2), in addition to the conditions listed in section 38, additions to buildings that increase the gross floor area of the building by more than 10.0 per cent but less than 75.0 per cent of the gross floor area legally existing as of June 09, 2014 must:
a
provide electrical isolation for the entire building through the placement of the master switch above the designated flood level; and,
4
Notwithstanding subsection (1), (2), and (3), in addition to the conditions listed in section 38, additions to buildings that increase the gross floor area of the building by at least 75.0 per cent of the gross floor area legally existing as of June 09, 2014 must:
a
an addition that does not increase the gross floor area of the building by more than 10.0 per cent of the gross floor area legally existing as of June 09, 2014;
b
a fence, gate, deck, landing, patio, skateboard and sports ramp, air conditioning unit, satellite dish, hot tub, above ground private swimming pool, and an Accessory Residential Building.
3
Notwithstanding subsection (1) and (2), additions that increase the gross floor area of the building by more than 10.0 per cent but less than 75.0 per cent of the gross floor area legally existing as of June 09, 2014 must:
a
provide electrical isolation for the entire building through the placement of the master switch a minimum of 0.3 metres above the highest grade existing on the adjacent street; and,
Division 4: Lighting Rules
Shielding
63
1
All outdoor light fixtures must be aimed and shielded in a manner that does not direct illumination onto a street or adjacent residential uses.
2
Unless otherwise referenced in subsection (3), all outdoor light fixtures must not emit light above the horizontal plane at the bottom of the light fixture.
3
Outdoor light fixtures may emit light above the horizontal plane at the bottom of the light fixture only where the light fixture:
Mounting of Fixtures
64
All outdoor light fixtures, other than those referenced in section 63(3), must be mounted with a rigid mounting arm with no adjustment feature.
Height Limits
65
1
Unless otherwise referenced in subsection (2), the maximum mounting height for an outdoor light fixture with a luminaire wattage greater than 100 watts is:
a
7.5 metres in the C-N1, C-N2, C-C1, C-COR1, CC-ER, I-B and I-E Districts and in all residential districts, mixed use districts and special purpose districts; and
b
12.0 metres in the CC-ET, CC-EIR, CC-EMU, CC-EPR, CC-ERR Districts and in all other commercial and industrial districts.
2
There is no maximum mounting height requirement for an outdoor light fixture with a luminaire wattage greater than 100 watts for an Outdoor Recreation Area and a Spectator Sports Facility, regardless in which District these uses are located.
3
Outdoor light fixtures mounted on poles, or any structure intended primarily for mounting lighting, must not exceed a mounting height of 40.0 per cent of the horizontal distance between the light fixture and the property line, except:
a
For outdoor light fixtures with a mounting height less than 5.0 metres with side shielding on the property line side of the outdoor light fixture so that the luminaire is not visible from the property line; and
4
Outdoor light fixtures with a luminaire wattage greater than 100 watts, mounted onto buildings, must not have a mounting height higher than the building or higher than 40.0 per cent of the horizontal distance between the light fixture and the property line, whichever is the lesser, except for:
a
outdoor light fixtures mounted on building façades that are less than 7.5 metres from the property line may have a mounting height of 3.0 metres or less; and
Canopy Lighting
66
Outdoor light fixtures mounted on canopies must be recessed so that the luminaire does not project below the underside of the canopy.
Division 5: Signs
Purpose
67
This Division is intended to regulate signs in order to:
d
prevent sign proliferation, to ensure that the effectiveness of informational and identification signage is not undermined through visual clutter.
Classification of Signs
68
All signs are classified as belonging to either Sign — Class A, Sign —Class B, Sign — Class C, Sign — Class D, Sign — Class E, Sign — Class F or Sign — Class G.
Development Permits
69
1
Unless specifically exempt from the requirement to obtain a development permit, all signs, structures for signs and any enlargement, relocation, erection, construction or alteration of a sign, require a development permit.
2
A development permit is not required for routine maintenance and repair, changing the copy, or reducing the copy area of a legally existing sign.
Comprehensive Sign Program
70
1
The Development Authority may require that any or all signs placed on a building or parcel comply with a comprehensive sign program as set out in a development permit affecting the parcel where signs are to be located.
2
The comprehensive sign program may set out a designated area for signs attached to or projecting from the face of a building or for any signs that are freestanding to be located on the parcel and any proposed signs must be located in the designated area or location for signs specified in the applicable development permit.
4
Where a development permit application for a sign is proposed that would conflict with the comprehensive sign program, the Development Authority will evaluate the application as if the proposed sign required a relaxation of the rules of this Bylaw.
5
A comprehensive sign program is only in place when a condition on a development permit affecting the parcel where signs are to be located clearly indicates that a comprehensive sign program has been approved.
6
When the architectural and site drawings that form part of a development permit indicate areas on a building wall for future tenant signage or parcel locations for signs that will be freestanding, these areas and locations are not to be interpreted as a comprehensive sign program unless a condition on the development permit clearly indicates that a comprehensive sign program has been approved.
Comprehensive Sign Program for Pedestrian Corridors
71
Where a building is proposed, or an existing building is undergoing exterior redevelopment on a parcel in one of the locations referenced in subsection 89(2) the Development Authority must consider implementing a comprehensive sign program in accordance with section 70 that would require signage that is appropriately scaled for pedestrians and takes into consideration the following:
a
a requirement for Projecting Signs or Canopy Signs to be installed so that business identification signage is visible to pedestrians on a public sidewalk;
d
the number and locations for any Temporary Signs or Freestanding Signs that would be located on the parcel.
Development Authority's Discretion
72
1
Where a type of sign is listed as a permitted use in a District, but does not comply with all of the applicable rules of this Part, the Development Authority's decision to relax a rule must be guided by the:
2
Where a type of sign is listed as a discretionary use in a District, the Development Authority's exercise of discretion must be guided by the:
Rules Governing All Signs
2
No sign, other than a Special Event Sign or an approved Sign — Class F or Sign — Class G, may display third party advertising.
5
Signs in residential districts must not be internally illuminated, but may be illuminated indirectly in a manner that prevents the trespass of light onto adjacent parcels.
6
Signs, sign supports and structures for signs must be located a minimum of 0.75 metres back from a curb line.
7
Signs must not be placed in or on motor vehicle parking stalls or loading stalls and must be placed to not reduce the number of motor vehicle parking stalls or loading stalls required pursuant to this Bylaw or a development permit.
8
Signs must not be placed within a corner visibility triangle where any part of the sign is higher than 0.75 metres and lower than 4.6 metres above the lowest elevation of the street.
9
Signs, sign supports and structures for signs must not be located in the Required Setbacks referenced in section 53 and Table 1.
10
The Development Authority may only relax the requirements in subsection (9) if the sign owner agrees, in writing, to remove the sign from its location within 30 days of being asked to remove it by the City.
a
the sign owner agrees in writing to remove the sign from its location within 30 days of being asked to remove it by the City;
b
the sign will have a minimum clearance of 4.6 metres over a City owned driveway, lane or alley; and
c
the sign will have a minimum clearance of 2.4 metres in any instance not referenced in subsection (b).
13
The Development Authority may only relax the requirement of subsection (12) if the Development Authority is satisfied that new trees or shrubs will be planted to replace any trees and shrubs that are removed or damaged and that the new plantings are consistent with any conditions respecting landscaping on a development permit for the parcel where the sign is located.
73.1
1
In addition to the rules contained in this Division, signs located in the Stephen Avenue Mall heritage area must not obscure or adversely impact historical architectural details of a building's facade.
2
Notwithstanding section 93(3.1), signs located within the Stephen Avenue Mall heritage area may utilize only the following means of illumination:
4
With the exception of signs referenced in sections 90 (3) and 99 (5), the text of a sign located in the Stephen Avenue Mall heritage area must not occupy more than 60.0 per cent of the total sign area.
74
1
Copy shown on a digital display must be static and remain in place for a minimum of six (6.0) seconds before switching to the next copy.
4
Copy must not be shown on the digital display using full motion video or otherwise give the appearance of animation or movement, and the transition between each digital copy must not be displayed using any visible effects, including but not limited to action, motion, fading in and out, dissolving, blinking, intermittent, or flashing light or the illusion of such effects.
5
Copy must not be shown in a manner that requires the copy to be viewed or read over a series of sequential copy messages on a single digital display, or sequenced on multiple digital displays.
5.2
A sign containing a digital display must not increase the light levels adjacent to the digital display by more than 3.0 LUX above the ambient light level.
6
The sign owner must ensure that while the sign is in operation, the light output for the digital display must be set in accordance with the following maximum luminance levels when measured from the sign face at its maximum brightness:
8
If any component on the sign fails or malfunctions in any way or fails to operate as indicated on the approved development permit plans, the sign owner must ensure that the sign is turned off until all components are fixed and operating as required.
9
The sign owner must provide the Development Authority with a name and telephone contact information of a person(s) having access to the technology controls for the sign, who can be contacted 24 hours a day in the event that the sign malfunctions.
Maintenance of Signs
b
replace it with a new sign that complies with any applicable development permit or the rules of this Bylaw where a development permit is not required; or
Parcels in Related Function
76
Where abutting parcels have the appearance and function of a single site by virtue of having cross-access easements, shared parking, connecting internal roadways, or common access points, a sign that relates to a use on any of the parcels will not be considered a Third Party Advertising Sign simply because it is located on another parcel.
Rules Governing Class A Signs
77
A Sign — Class A does not require a development permit when "Sign — Class A" is a listed use in the District and the sign meets all applicable rules.
Address Sign
78
1
Where an Address Sign is sculpted out of the face of a building and is not illuminated, there is no maximum copy area restriction.
2
Where an Address Sign is affixed to a residence or a private garage, the maximum copy area is 0.30 square metres.
3
Where an Address Sign is neither sculpted out of a building or affixed to a residence or private garage, the maximum copy area is 1.2 square metres.
4
Any proposed Address Sign that exceeds the maximum copy area set out in this section will be considered a Fascia Sign or Freestanding Sign and must comply with the rules applicable to those signs.
Art Sign
b
the name of any individual, organization or business that sponsored or contributed to making the Art Sign.
3
When an Art Sign takes the form of a Window Sign it must follow all rules applicable to a Window Sign as referenced in section 90.
Banner Sign
2
A Banner Sign that is used to temporarily promote the buying or selling of products or services or to announce the opening of a business:
b
is limited to one per business provided there is not more than one Banner Sign located on a building at any one time.
3
A Banner Sign that is used in place of a Fascia Sign may only be placed in the designated signable area and locations referenced in section 92 for a period not exceeding 90 days following the issuance of a development completion permit or occupancy permit granted under the Building Permit Bylaw for the development to which the sign relates.
b
freestanding provided it does not exceed 3.0 metres in height when measured from grade to the highest part of the sign.
Construction Sign
81
1
All Construction Signs relating to undeveloped parcels, or parcels where the development is being carried out in accordance with a development permit:
Directional Sign
2
A Directional Sign must not have any advertising copy or slogans, but may have logos and written identification copy.
5
A maximum of two freestanding Directional Signs may be located near any point of ingress or egress to the parcel when the Directional Sign intends to direct a vehicle or pedestrian onto the parcel.
Flag Sign
2
A Flag Sign and the structures they are on must not extend higher than the maximum height allowed for a Freestanding Sign as referenced in section 97.
Pedestrian Sign
85
1
Each business in a building that is located on the floor closest to grade may have one Pedestrian Sign provided it does not exceed:
3
A Pedestrian Sign must be located within 3.0 metres of a public entrance that serves the business to which the sign relates unless it is located on a parcel in one of the locations referenced in subsection 89(2).
Real Estate Sign
86
1
A Real Estate Sign may take the form of any other type of sign or be incorporated into an existing Freestanding Sign.
b
the Real Estate Sign may have a maximum sign area of 1.5 square metres and a maximum height of 2.0 metres above grade, if the frontage is equal to or less than 30 metres; and
c
the Real Estate Sign may have a maximum sign area of 3.0 square metres and a maximum height of 3.0 metres above grade, if the frontage is greater than 30.0 metres.
3
When a Real Estate Sign takes the form of a Fascia Sign it must follow all rules applicable to a Fascia Sign as referenced in section 92 and 93.
Special Event Sign
87
1
A Special Event Sign located in a low density residential district may only be located on a parcel that does not contain a Dwelling Unit.
2
A Special Event Sign must not contain advertising copy beyond copy that promotes the special event, but may contain copy acknowledging the name of an individual, organization or business that sponsors or contributes to the special event.
4
A Special Event Sign may be displayed for up to 15 days prior to the date of the special event to which it relates and for the duration of the special event, but must not be displayed for more than 30 days in total.
Temporary Sign
89
1
A Temporary Sign must not be located on any parcel such that the copy on the sign is visible from:
2
A Temporary Sign must not be placed on a parcel that is located in the following pedestrian corridors:
2.1
A Temporary Sign must not be placed on a parcel where an approved Digital Message Sign is operating.
3
A Temporary Sign must be stabilized and anchored in a way that ensures it will not be unintentionally moved, blown over or dislocated.
4
Sandbags and guy wires may only be used to stabilize or anchor a Temporary Sign if the sign is located on a hard surface.
a
1.0 square metre if a Dwelling Unit is located on the parcel where the Temporary Sign is located; and
b
3.0 square metres if there are no Dwelling Units located on the parcel where the Temporary Sign is located, with the exception of election signs.
7
In all other Districts not addressed by subsection (6), the maximum sign area of a Temporary Sign is:
a
1.5 square metres if the frontage of the parcel where the Temporary Sign is located is 30.0 metres or less; and
b
5.5 square metres if the frontage of the parcel where the Temporary Sign is located is greater than 30.0 metres.
b
2.0 metres if the sign area is greater than 2.5 square metres, but less than 3.0 square metres; and
9
A Temporary Sign with a sign area greater than 1.5 square metres must be located on a Temporary Sign Marker that has been approved in accordance with the rules for Sign — Class E and must:
10
Unless otherwise referenced in subsection (11) a maximum of one Temporary Sign may be located on a parcel.
b
greater than 75.0 metres, but less than or equal to 200.0 metres, a maximum of two Temporary Signs may be located on that parcel; and
90
1
The total copy area of one or more Window Signs must not exceed 30.0 per cent of the window area.
c
be located within 1.8 metres of a window where the sign is internally illuminated and facing outward from inside a building; and
Designated Signable Area and Locations for Fascia Signs
92
1
Unless otherwise referenced in subsections (4) and (5), Fascia Signs must be located within the designated signable area described in this section.
5
A Fascia Sign may be located below the designated signable area referenced in subsections (2) and (3) provided:
Sign Illustration 3: Designated Signable Area Subsections 92(2), (3) and (4)
Rules for Fascia Signs
93
1
A Fascia Sign does not have a maximum sign area when located on a primary building wall and within the designated signable area on that wall.
2
The maximum total sign area for all Fascia Signs located on a secondary building wall is 30.0 per cent of the designated signable area on that wall.
3
A Fascia Sign located on a secondary building wall may be illuminated, but must only be indirectly illuminated when the copy of the sign is visible from:
Sign Illustration 4:
Sign Area on Secondary Building Wall
Subsection 93(2)
Rules Governing Class C Signs
94
1
A development permit is not required to add additional panels to a legally existing Freestanding Sign when:
b
the panel sought to be added is the same length as any message panels already on the Freestanding Sign;
d
the addition of the panel would not result in the Freestanding Sign violating any rules respecting maximum height, copy, clearance or location or any conditions of the approved development permit for the Freestanding Sign.
Rules for Freestanding Signs
4
A proposed Freestanding Sign must be located a minimum of 30.0 metres from any other Freestanding Sign located on an adjacent parcel that is:
Number of Freestanding Signs
96
1
Unless otherwise referenced in subsections (2) and (3), a parcel may have a maximum of one Freestanding Sign facing each street that provides access to the parcel.
2
Where a parcel has a frontage equal to or greater than 200.0 metres, one additional Freestanding Sign for every 200.0 metres of frontage is allowed on the applicable frontage in addition to the Freestanding Sign allowed in accordance with subsection (1).
3
Where a parcel is designated the C-R2 or C-R3 District, two additional Freestanding Sign are allowed per frontage in addition to those Freestanding Signs allowed in accordance with subsections (1) and (2).
Size and Height Restrictions for Freestanding Signs
3
In the CC-ET and CC-EIR Districts, and all other commercial and in all industrial and mixed use districts:
Rules Governing Class D Signs
98
1
A development permit is required to erect a new canopy, awning, marquee or projecting structure intended to display a Sign — Class D and must follow any applicable dimensional standards referenced in sections 99, 100, 101 and 102.
2
A development permit is not required for a change in copy for a Sign — Class D when the canopy, awning, marquee or projecting structure legally exists even if the applicable sign structure does not meet the dimensional standards referenced in sections 99, 100, 101 and 102.
Rules for Canopy Signs
99
1
The copy area on a Canopy Sign must not exceed 50.0 per cent of the total area of the canopy which will be measured by the vertical height of the canopy multiplied by the length of the canopy or awning.
d
not exceed 1.5 metres in height measured from the lowest point of the structure to the highest point of the structure.
Sign Illustration 5: Rules for Canopy Signs Subsections 99(1) and (3)(a)
b
has a maximum copy area not greater than 30.0 per cent of the total area of the canopy which will be measured by the vertical height of the canopy multiplied by the length of the canopy awning;
d
may contain a valance with copy that is no greater than 80.0 per cent of the height of the valance.
Rules for Projecting Signs
1.1
In the Stephen Avenue Mall heritage area, a Projecting Sign must be limited to a maximum of one for every 7.5 metre section of building façade parallel to Stephen Avenue Mall;
2
The edge of a Projecting Sign closest to the wall of the building to which it is attached must be within 0.30 metres of that wall.
3
Unless otherwise referenced in subsection (4), the maximum height of a Projecting Sign is 6.0 metres from grade when measured to the top of the sign.
4
Where a Projecting Sign relates to a Hotel, Retail and Consumer Service or a Parking Lot — Structure with a height of 18.5 metres or greater, the maximum height of the Projecting Sign is 21.5 metres above grade so long as:
Size Restrictions for Projecting Signs
3
In all other commercial districts, in all industrial and mixed use districts and in the CC-ET and CR20-C20/R20 Districts the maximum sign area for a Projecting Sign is 4.5 square metres.
4
In all other Districts not referenced in subsections (1) through (3), the maximum sign area for a Projecting Sign is 1.0 square metres.
a
must not have a dimension greater than 0.91 metres by 1.22 metres except where the only other sign on the façade of the building is a Window Sign; and
b
when located above the designated signable area referenced in section 92(2) and (5) must not have a:
104
1
Unless otherwise referenced in subsection (2), a Digital Message Sign may only be approved in a commercial district, industrial district, mixed use district, S-R, CC-ER or CR20-C20/R20 District.
3
A maximum of one Digital Message Sign may be located on a parcel with the exception that corner parcels may have one Digital Message Sign on the street side of each street.
4
Subsection (3) does not apply to a Digital Message Sign with copy that only displays the date, time, temperature, motor vehicle parking stall information, motor vehicle fuel price or a Drive Through menu board.
5
Notwithstanding subsection (3), a Digital Message Sign must not be located on a parcel adjacent to Deerfoot Trail, Spruce Meadows Trail, Stoney Trail, or any provincial highway under the Highways Development and Protection Act when the copy on the sign is visible from these streets or highways.
5.1
Notwithstanding subsection (5), a Digital Message Sign may be located on a parcel adjacent to Deerfoot Trail, Spruce Meadows Trail, Stoney Trail or any provincial highway under the Highways Development and Protection Act when in accordance with Table 1.1.
Table1.1: Maximum Digital Message Sign areas facing the same oncoming traffic and minimum distance from Deerfoot Trail, Spruce Meadows Trail, Stoney Trail or provincially controlled highway
5.2
The Development Authority must not relax the minimum distance from the edge of pavement to a Digital Message Sign as shown in Table 1.1.
a
where located in a commercial district, industrial district, mixed use district, S-R, CC-ER or CR20-C20/R20 District has a maximum sign area:
ii
not exceeding the lesser of 2.5 square metres or 30.0 percent of the window area, where used as a Window Sign;and
b
where located in a low-density residential district, multi-residential district, CC-MH, CC-MHX, S-SPR, S-CS, S-CI, S-URP, CC-EMU, CC-ET, CC-EPR, CC-EIR and CC-ERR Districts, has a maximum sign area of 1.0 square metres.
7
Where the digital display of a Digital Message Sign is visible from and located within 125.0 metres of a building containing a Dwelling Unit, the sign must not operate, or must only display a black screen when located in:
a
a commercial district, industrial district, mixed use district, S-R, CC-ER or CR20-C20/R20 District, between 11 p.m. and 6 a.m.; or
b
one of the districts and associated with one of the uses listed in subsection (2), between 10 p.m. and 7 a.m.
8
A Digital Message Sign, or any digital copy on a Digital Message Sign must not be located on or attached to a roof of a building.
9
The Development Authority must not approve any sign containing a digital display with a sign area greater than 2.0 square metres if the sign is located less than 30.0 metres from an intersection, pedestrian crosswalk, or railway crossing.
11
A Digital Message Sign may display copy that acknowledges sponsors of activities or programs when the sign is associated with one of the following uses:
12
A development permit for a Digital Message Sign may only be issued for a period not exceeding three (3) years, except where copy only displays the date, time, temperature, motor vehicle fuel price, or Drive Through menu board.
13
Prior to a development permit expiring for a Digital Message Sign, and upon receipt of a new development permit application for the same Digital Message Sign, the Development Authority:
a
must ensure the location of the Digital Message Sign does not interfere with information signs in road rights-of-way;
b
must, when a sign is located in a district referenced in subsection (1), apply the rules referenced in subsection (7); and
c
may approve the development permit for a Digital Message Sign that was approved prior to March 1, 2013, and is adjacent to Deerfoot Trail.
Inflatable Sign
105
1
An Inflatable Sign is not allowed in those locations referenced in subsections 89(1) or 89(2).
3
An Inflatable Sign must be tethered or anchored and must touch the surface to which it is anchored.
4
An Inflatable Sign must not extend higher than the maximum height allowed for a Freestanding Sign as referenced in section 97.
Painted Wall Sign
1.1
In the Stephen Avenue Mall heritage area, a Painted Wall Sign must only be located on a building façade perpendicular to Stephen Avenue Mall.
2
If a Painted Wall Sign is removed, the wall it was displayed on must be refinished to be consistent with the rest of the building.
4
A Roof Sign and the supports for a Roof Sign, must not extend beyond the maximum building height applicable to the District where the sign is located.
2
A Rotating Sign must not exceed the maximum height and maximum sign area allowed for a Freestanding Sign as referenced in section 97.
Temporary Sign Markers
109
1
A Temporary Sign Marker is not allowed in those locations where a Temporary Sign is not allowed as referenced in subsections 89(1) and 89(2).
3
The number of Temporary Sign Markers allowed on a parcel must not exceed the number of Temporary Sign allowed on the applicable parcel as referenced in subsections 89(10) and 89(11).
5
If a Temporary Sign is intended to be illuminated, the Temporary Sign Marker must have an underground power supply.
6
A Temporary Sign Marker must be accessible from the parcel on which it is located so that no person has to cross a different parcel, or City owned boulevard in order to install, do maintenance on, or remove a Temporary Sign.
3
Third Party Advertising Signs are prohibited on any site where the sign is positioned such that the copy on the sign is visible from:
f
17 Avenue South from the eastern City limit, west to the Canadian National Railway crossing of 17 Avenue South near 52 Street S.E.;
hh
McKnight Boulevard from Deerfoot Trail east to Barlow Trail and from 36 Street N.E., east to the City limits;
mm
Sarcee Trail from the Trans-Canada Highway, south to the junction of Glenmore Trail and from Southland Drive, south to the City limits;
4
Third Party Advertising Signs are prohibited on sites adjacent to Bowness Road from 62 Street N.W. to 65 Street N.W.
when the copy is visible.
7
Notwithstanding subsection 111(3)(tt), existing Third Party Advertising Signs positioned such that the copy is visible from the Trans Canada Highway between the Bow River and Bowfort Road and approved prior to November 19, 1990 may be renewed from time to time in accordance with subsections 114 (10) and (11).
8
Notwithstanding subsection 111(3)(y) and (uu), existing Third Party Advertising Signs positioned such that the copy is visible from Glenmore Trail S.E. or from the Trans-Canada Highway between 6 Street N.E. and 36 Street N.E. respectively, may be renewed from time to time in accordance with subsections 114 (10) and (11).
9
Notwithstanding subsection 111(3), freestanding-flush and wallmounted Third Party Advertising Signs in commercial or industrial districts may be allowed along those public thoroughfares referred to in subsections 111(3)(f)(q)(u) and (nn) where:
b
the sign is not positioned such that it can be viewed from a land use district other than a commercial or industrial districts; and
10
Notwithstanding subsection 112(4), where an existing Third Party Advertising Sign complies with this Bylaw, except for the provisions of subsection 111(4), it may be renewed from time to time in accordance with subsections 114 (10) and (11).
11
Notwithstanding subsections 111(3)(hh) and (kk), where an existing Third Party Advertising Sign complies with this Bylaw, except for the provisions of subsections 111(3)(hh) and (kk), it may be renewed from time to time in accordance with subsections 114 (10) and (11).
12
Unless otherwise referenced in subsection (13), and upon receipt of a new development permit application for the same Third Party Advertising Sign, no Third Party Advertising Sign may be approved within the Inglewood Main Street Area after November 9, 1992.
13
A development permit for a Third Party Advertising Sign may be approved in the Inglewood Heritage Main Street Area if such sign replaces an existing Third Party Advertising Sign of the same or greater area at the same or another location in the Inglewood Heritage Main Street Area provided always that the approval of such a sign may only be allowed where it will result in a visual improvement to the character and streetscape of the area and either:
14
A development permit for a Third Party Advertising Sign may only be approved in the Mainstreet portion of Bowness Road NW when such a sign:
a
replaces an existing Third Party Advertising Sign of the same or greater area at the same location provided; and
Siting of Third Party Advertising Signs
112
1
A Third Party Advertising Sign must not be located within 30.0 metres of any Freestanding Sign, facing the same oncoming traffic, except where the separation is between existing signs approved prior to November 19, 1990.
2
A Third Party Advertising Sign must be removed from a parcel upon expiry of the development permit for such sign if a development permit application for a Freestanding Sign is approved within 30.0 metres of the Third Party Advertising Sign.
3
A Third Party Advertising Sign must not be located within 75.0 metres of any other Third Party Advertising Sign facing the same on-coming traffic and must not result in more than two (2) freestanding Third Party Advertising Signs greater than 4.6 metres in height and 4.5 square metres in area within a 225.0 metre radius of each other facing the same street, except:
a
where the separation is between an existing Third Party Advertising Sign, approved prior to June 19, 2000;
c
for a Third Party Advertising Sign, less than 4.6 metres in height and 4.5 square metres in area, where the separation must be 30.0 metres.
4
Subject to subsections (1) and (3), a Third Party Advertising Sign, less than 4.6 metres in height and 4.5 square metres in area, must not be located closer than 30.0 metres to any other Third Party Advertising Sign less than 4.6 metres in height and 4.5 square metres in area.
5
A Third Party Advertising Sign must be located such that no portion is less than 6.0 metres from any property line adjacent to a public thoroughfare except for Third Party Advertising Signs less than 4.6 metres in height and 4.5 square metres in area.
6
Notwithstanding subsection (5), where an existing Third Party Advertising Sign complies with this Bylaw, except for the provisions of subsection (5), it may be renewed from time to time in accordance with subsections 114 (10) and (11).
7
Trees required under an approved development permit shall not be removed or altered in any way to accommodate the placement or visibility of a Third Party Advertising Sign.
c
the curbline or edge of a major street, expressway or freeway; to the satisfaction of the General Manager Transportation or his delegate.
Height and Size of Third Party Advertising Signs
113
1
The maximum height of a wall-mounted or a freestanding-flush Third Party Advertising Sign is 10.5 metres and it must not extend above the eaveline.
2
The maximum height of a freestanding Third Party Advertising Sign is 8.3 metres, and if any portion of a freestanding Third Party Advertising Sign is located within 6.5 metres of a building less than 8.3 metres in height, the sign must not exceed the height of that building or 6.5 metres, whichever is greater.
2.1
In the C-COR1, C-COR2, CC-X and CC-COR Districts, where located outside of pedestrian-oriented areas as referenced in subsection 113 (6), the maximum height of a Third Party Advertising Sign is 4.6 metres and the maximum sign area is 4.5 square metres.
3
The dimensions of the sign area of a Third Party Advertising Sign must not exceed a vertical dimension of 5.8 metres by a horizontal dimension of 7.0 metres, with allowance for a 1.5 metre cut-out to the top and face and a 0.70 metre cut-out to the sides and bottom of the Third Party Advertising Sign.
4
The maximum area of a Third Party Advertising Sign must not exceed 25.0 square metres and only one face of a double-faced sign may be used to calculate sign area.
5
Where an existing Third Party Advertising Sign complies with this Bylaw, except for the provisions of this section, it may be renewed from time to time in accordance with subsections 114 (10) and (11).
General Rules for Third Party Advertising Signs
114
1
The applicant for a development permit for a Third Party Advertising Sign must show that the Third Party Advertising Sign is compatible with the general architectural lines and forms of nearby buildings and the character of the streetscape or area within which it is to be located, and does not severely obstruct the horizon line.
1.1
Third Party Advertising Signs with a sign area greater than 4.5 square metres may only be located in the CR20-C20/R20 District where:
2
A Third Party Advertising Sign must not block natural light or the sky from the surrounding buildings' windows and doors.
3
The lighting or orientation of a Third Party Advertising Sign must not adversely affect any neighbouring residential areas.
4
A Third Party Advertising Sign must utilize lighting fixtures which are not readily discernible or obtrusive.
5
An auxiliary sign or other material must not be attached to, on, above or below a Third Party Advertising Sign.
8
Electrical power supply to Third Party Advertising Signs or base landscaping must be underground unless otherwise allowed by the Development Authority such as, but not limited to, situations where reasonable access to an underground power source is not available or the Third Party Advertising Sign is located in an area where underground power has not commenced.
9
A development permit for a Third Party Advertising Sign may only be issued for a period not exceeding five (5) years.
10
Prior to a development permit expiring for a Third Party Advertising Sign, and upon receipt of a new development permit application for the same Third Party Advertising Sign at the same height, size and location, the Development Authority may apply the rules referenced in subsection (11).
11
When considering a development permit application for a Third Party Advertising Sign referenced in subsection (10), the Development Authority:
a
must consider if the proposed Third Party Advertising Sign is compatible with the general architectural lines and forms of nearby buildings and the character of the streetscape or area within which it is to be located, and does not severely obstruct the horizon line;
b
must not approve the development permit if a Freestanding Sign has been approved and constructed within 30.0 metres of the Third Party Advertising Sign;
c
may only approve the development permit for the Third Party Advertising Sign when the use is listed in the District;
d
may approve the development permit for the Third Party Advertising Sign if it is located in pedestrian-oriented areas as referenced in subsection 113 (6) at its current size and height provided the parcel has not been approved for redevelopment; and
e
may approve the development permit for the Third Party Advertising Sign if it is located in areas referenced in subsection 113 (2.1), when the height of the sign exceeds 4.6 metres and the area exceeds 4.5 square metres at their current size and height provided the parcel has not been approved for redevelopment.
Major Parks
1. West Nose Creek Park
2. Nose Hill Park
3. Nose Creek Park
4. Prairie Winds Park
5. Confederation Park
6. Baker Park
7. Bowness Park
8. Bowmont Park
9. Shouldice Park
10. Edworthy Park
11. Lawrey Gardens
12. Riley Park
13. Millennium Park & Science Centre
14. Prince's Island Park
15. Olympic Plaza
16. Fort Calgary
17. Calgary Zoo & St. Patrick's Island
18. Tom Campbell's Hill
19. Pearce Estate Park
20. Inglewood Bird Sanctuary
21. Valleyview Park
22. Marlborough Park
23. Elliston Park
24. Richmond Green Park
25. Lindsay Park
26. Stanley Park
27. River Park & Sandy Beach
28. North Glenmore Park
29. Weaselhead Natural Area
30. South Glenmore Park
31. Heritage Park
32. Beaver Dam Flats Park
33. Carburn Park
34. Southland Park
35. Fish Creek Provincial Park
36. Griffith Woods
37. Ralph Klein Park
38. 12 Mile Coulee Park
Map 3: Major Parks
Prohibited Locations for Digital Third Party Advertising Signs
2
Digital Third Party Advertising Signs are prohibited on any site where the sign is positioned such that the copy on the sign is visible from:
f
17 Avenue South from the eastern City limit, west to the Canadian National Railway crossing of 17 Avenue South near 52 Street S.E.;
mm
Sarcee Trail from the Trans-Canada Highway, south to the junction of Glenmore Trail and from Southland Drive, south to the City limits;
3
Digital Third Party Advertising Signs are prohibited on sites adjacent to Bowness Road from 62 Street N.W. to 65 Street N.W.
when the copy is visible.
b
is located less than 125.0 metres, measured from the face of the digital display to a building containing a Dwelling Unit
Siting of Digital Third Party Advertising Signs
115.3
1
A Digital Third Party Advertising Sign must not be located within 30.0 metres of any Freestanding Sign, facing the same oncoming traffic;
2
A Digital Third Party Advertising Sign must be removed from a parcel upon expiry of the development permit for such a sign if a development permit application for a Freestanding Sign is approved within 30.0 metres of the Digital Third Party Advertising Sign;
a
must be located at least 300.0 metres from any other Digital Message Sign or Digital Third Party Advertising Sign when measured from the closest point of the sign containing the digital display and to the closest point of another sign containing the digital display when the signs are facing the same oncoming traffic;
b
must not be located within 75.0 metres of any Third Party Advertising Sign facing the same on-coming traffic and must not result in more than two (2) signs displaying third party advertising greater than 4.6 metres in height and 4.5 square metres in area within a 225.0 metre radius of each other facing the same street;
c
except where specified in subsection (d), must be located at least the following distances from any property line shared with a street:
i
17.0 metres where the posted speed limit of the public thoroughfare is 100 kilometres per hour or greater;
iv
10.0 metres where the posted speed limit of the public thoroughfare is 70 kilometres per hour; and
d
may be located closer to a property line shared with a street identified in subsection (c) provided that:
iii
the distance from the sign to any property line is not less than that of the existing approved Sign — Class F.
4
Trees required under an approved development permit must not be removed or altered in any way to accommodate the placement or visibility of a Digital Third Party Advertising Sign.
5
A Digital Third Party Advertising Sign must not be located on, or attached to, a roof of a building.
c
the curbline or edge of a major street, expressway or freeway, to the satisfaction of the General Manager Transportation or his delegate.
Height and Size of Digital Third Party Advertising Signs
115.4
1
The maximum height of a wall-mounted or a freestanding-flush Digital Third Party Advertising Sign is 10.5 metres and it must not extend above the eaveline.
2
The maximum height of a freestanding Digital Third Party Advertising Sign is 8.3 metres, and if any portion of a freestanding Digital Third Party Advertising Sign is located within 6.5 metres of a building less than 8.3 metres in height, the sign must not exceed the height of that building or 6.5 metres, whichever is greater.
3
The dimensions of the sign area of a Digital Third Party Advertising Sign must not exceed a vertical dimension of 5.8 metres by a horizontal dimension of 7.0 metres, with allowance for a 1.5 metre cut-out to the top and face and a 0.70 metre cut-out to the sides and bottom of the Digital Third Party Advertising Sign.
4
The maximum area of a Digital Third Party Advertising Sign must not exceed 25.0 square metres and only one face of a double-faced sign may be used to calculate sign area.
General Rules for Digital Third Party Advertising Signs
115.5
1
The applicant for a development permit for a Digital Third Party Advertising Sign must show that the Digital Third Party Advertising Sign is compatible with the general architectural lines and forms of nearby buildings and the character of the streetscape or area within which it is to be located, and does not severely obstruct the horizon line.
1.1
Digital Third Party Advertising Signs with a sign area greater than 4.5 square metres may only be located in the CR20-C20/R20 District where:
2
A Digital Third Party Advertising Sign must not block natural light or the sky from surrounding buildings' windows and doors.
3
The lighting or orientation of a Digital Third Party Advertising Sign must not adversely affect any neighbouring residential areas.
4
An auxiliary sign or other material must not be attached to, on, above or below a Digital Third Party Advertising Sign.
6
The space between the faces of a double-faced Digital Third Party Advertising Sign must be enclosed.
7
Electrical power supply to the Digital Third Party Advertising Sign or base landscaping must be underground unless otherwise allowed by the Development Authority such as, but not limited to, situations where reasonable access to an underground power source is not available or the Digital Third Party Advertising Sign is located in an area where underground power has not commenced.
8
A development permit for a Digital Third Party Advertising Sign may only be issued for a period not exceeding three (3) years.
9
Prior to a development permit expiring for a Digital Third Party Advertising Sign, and upon receipt of a new development permit application for the same Digital Third Party Advertising Sign at the same height, size and location, the Development Authority may apply the rules referenced in subsection (10).
10
When considering a development permit application for a Digital Third Party Advertising Sign referenced in subsection (9), the Development Authority:
a
must consider if the proposed Digital Third Party Advertising Sign is compatible with the general architectural lines and forms of nearby buildings and the character of the streetscape or area within which it is to be located, and does not severely obstruct the horizon line;
b
must not approve the development permit if a Freestanding Sign has been approved and constructed within 30.0 metres of the Digital Third Party Advertising Sign;
c
may only approve the development permit for the Digital Third Party Advertising Sign when the use is listed in the District; and
d
must not approve the development permit for the Digital Third Party Advertising Sign when the sign is located within and the digital display is visible from 125.0 metres of a building containing a Dwelling Unit.
Division 6: Requirements for Motor Vehicle Parking Stalls, Bicycle Parking Stalls and Loading Stalls
116
Motor vehicle parking stalls, visitor parking stalls, bicycle parking stalls and loading stalls required for a use may only be located on a separate parcel from the use where:
b
all parcels forming part of the comprehensive development are indicated on the same development permit.
Parking Stall Signage
117
1
Permanent signage must identify and restrict the use of motor vehicle parking stalls as being only for the purpose required for:
a
residents of Dwelling Units that are not Single Detached Dwellings, Semi-detached Dwellings or Duplex Dwellings;
Location of Parking and Loading Requirements
118
1
The minimum number of motor vehicle parking stalls, visitor parking stalls and bicycle parking stalls for a development are specified in Part 4, General Rules for Multi-Residential Districts and the land use districts.
3
Where the minimum number of visitor parking stalls, bicycle parking stalls or loading stalls for a development is not specified, the Development Authority must determine the minimum number of stalls for that development in consideration of the minimum number of stalls for other developments with similar characteristics and other relevant information.
Use of Parking and Loading Stalls
119
Motor vehicle parking stalls must be used and made available only for the purpose for which they were approved.
Identification of Required Parking and Loading Stalls
120
A plan forming part of a development permit must:
a
show the location, number and size of motor vehicle parking stalls, visitor parking stalls, bicycle parking stalls, pick-up and drop-off stalls and loading stalls;
Calculation of the Minimum Number of Required Parking and Loading Stalls
121
1
When the calculation of the minimum number of required motor vehicle parking stalls, bicycle parking stalls, visitor parking stalls or loading stalls results in a fractional number of stalls, the next higher whole number must be the minimum requirement for:
2
For uses other than Dwelling Units and Live Work Units, the following must be calculated separately:
Required Motor Vehicle Parking Stalls for Calculating Barrier Free Parking Stalls
121.1
Where the minimum number of motor vehicle parking stalls is not specified in Part 4, Table 1.2 provides the minimum parking requirements for the purpose of calculating the number of barrier free designated stalls for use by persons with physical disabilities in accordance with the National Building Code.
Table 1.2: Minimum Motor Vehicle Parking Requirements for Calculating Required Barrier Free Parking Stalls
Table 1.2: Minimum Motor Vehicle Parking Requirements for Calculating Required
Barrier Free Parking Stalls — continued
Table 1.2: Minimum Motor Vehicle Parking Requirements for Calculating Required Barrier Free Parking Stalls — continued
Table 1.2: Minimum Motor Vehicle Parking Requirements for Calculating Required Barrier Free Parking Stalls — continued
Table 1.2: Minimum Motor Vehicle Parking Requirements for Calculating Required Barrier Free Parking Stalls — continued
Standards for Motor Vehicle Parking Stalls
122
1
Unless otherwise specified, the minimum width and depth of motor vehicle parking stalls are illustrated in Table 2.
Table 2: Minimum Dimensions for Motor Vehicle Parking Stalls
2
The angle of a motor vehicle parking stall must be 90 degrees or must be between 75 degrees and 45 degrees. Motor vehicle parking stall dimensions between 45 degrees and 75 degrees must be calculated using a straight line interpolation between dimensions.
b
a Dwelling Unit where the stall is provided in a private garage intended to be used for the occupants of only one Dwelling Unit.
7
The minimum width of a motor vehicle parking stall for Multi- Residential Development, Multi-Residential Development — Minor, a Townhouse or a Rowhouse Building provided for the exclusive use of a Dwelling Unit is reduced to 2.60 metres where:
a
the stall is one of two or more motor vehicle parking stalls that are provided in a private garage;
b
the motor vehicle parking stalls in the private garage are for the sole use of the occupants of the Dwelling Unit; and
c
the motor vehicle parking stalls are only counted towards fulfilling the minimum motor vehicle parking stall requirements for that Dwelling Unit.
10
Motor vehicle parking stall dimensions must be clear of all obstructions, other than wheel stops and structural columns.
a
must not encroach into the width of the motor vehicle parking stall by more than a total of 0.30 metres;
14
Motor vehicle parking stalls must not be provided as tandem parking unless otherwise allowed in this Bylaw.
Loading Stalls
123
1
A loading stall must be located so that all motor vehicles using the stall can be parked and maneuvered entirely within the boundary of the site before moving onto a street or a lane.
4
Wheel stops must not exceed 0.10 metres in height above the loading stall surface and must be placed perpendicular to the loading stall depth a minimum of 0.60 metres from the front of the loading stall.
5
In commercial, industrial, mixed use and special purpose districts the minimum requirement for loading stalls is:
a
1.0 loading stalls per 9300.0 square metres of gross floor area where the cumulative gross floor area of all buildings on a parcel is greater than 930.0 square metres; and
b
0.0 loading stalls where the cumulative gross floor area of all buildings on a parcel is less than or equal to 930.0 square metres.
6
Unless otherwise referenced in subsection (7), the following uses are not included in the calculation of required loading stalls:
7
Where a building contains 20 or more units with shared entrance facilities, a minimum of 1.0 loading stalls is required.
8
In a multi-residential district, where the cumulative gross floor area of commercial multi-residential uses exceeds 930.0 square metres, the commercial multi-residential uses require 1.0 loading stalls per 9300.0 square metres of gross floor area.
Relaxations of Parking and Loading Stall Requirements
124
1
For uses in buildings listed on the City inventory of evaluated historic resources, the Development Authority may consider a relaxation of the minimum motor vehicle parking stalls, visitor parking stalls, bicycle parking stalls and loading stall requirements. Consideration for relaxations must be based on:
b
the existing ability of the site to accommodate motor vehicle parking stalls, visitor parking stalls, loading stalls and bicycle parking stalls; and
c
the number of motor vehicle parking stalls, visitor parking stalls, loading stalls and bicycle parking stalls to be relaxed.
2
The Development Authority may consider a relaxation in the required motor vehicle parking stalls and visitor parking stalls for uses when a transportation demand management measure is approved by the Development Authority and is required to be implemented as a condition in a development permit.
b
include requirements that must be incorporated into an approved plan or condition on a development permit.
4
The Development Authority may consider a relaxation in the minimum required motor vehicle parking stalls, visitor parking stalls, loading stalls and bicycle parking stalls for a development when:
b
the type of use, the size or shape of the parcel, or the topographical constraints present practical difficulties in accommodating the requirements of this Bylaw; when a relaxation is given for this reason, it and the reasons must be stated on the development permit; or
c
an applicant submits a parking study, as part of a development permit application, that demonstrates that the motor vehicle parking stall requirement, visitor parking stall or bicycle parking stall requirement should be less than the requirements of this Bylaw due to unique site, location or use characteristics, and the conclusions of the study are considered acceptable by the Development Authority.
5
The Development Authority may consider a relaxation to the minimum required pick-up and drop-off stalls for a School Authority — School when:
a
the proposed development is an addition to a School Authority — School building existing on the effective date of this Bylaw; or
b
the proposed development is a new School Authority — School building proposed on a parcel designated as reserve land existing on the effective date of this Bylaw; and
c
in the opinion of the Development Authority, it would be difficult to provide the required pick-up and drop-off stalls due to the parcel configuration, area of a parcel and frontage.
b
the development permit identifies the locations of the minimum required stalls, including the mechanisms used to maintain the stalls for the duration of the development;
c
the stalls referenced in subsection (b) are signed or marked as being available for the development; and
Bicycle Parking Stalls
2
Bicycle parking stalls — class 2 may only be located in hard surfaced areas and in hard surfaced landscaped areas.
4
Bicycle parking stalls must be separated from motor vehicle parking stalls, visitor parking stalls or loading stalls by 2.0 metres or a physical barrier.
6
A bicycle parking stall that is not an individual locker and is attached to the ground must be located at least 0.6 metres from any physical barrier.
7
Rows of bicycle parking devices, when affixed on the floor or grade, must be separated by at least 2.0 metres.
8
Bicycle parking devices, when affixed on the floor or grade, must be separated by at least 0.6 metres.
9
Required bicycle parking stalls — class 2 should be located within 15.0 metres of the public entrance of a building containing the uses for which they are required.
10
Directional signage indicating the location of minimum required bicycle parking stalls — class 2 must be provided when the stalls are not obviously visible near the entrance to a building.
Motor Vehicle Pick-Up and Drop-Off Stalls
b
within a street, if approved by the Development Authority and the General Manager of Transportation or his delegate.
2
The minimum dimensions of a pick-up and drop-off stall are the same as those for motor vehicle parking stalls provided in Table 2, except that a pick-up and drop-off stall that is parallel to a street, driveway or curb has a minimum width of 2.6 metres and a minimum depth of 6.7 metres.
Division 7: Requirements for Infrastructure Servicing
129.1
The Development Authority must confirm there is adequate sewage collection, treatment and disposal, water supply, treatment and distribution, storm water collection and storage and road infrastructure capacity necessary to serve the development.